Plumbing Basics: What You Need for Bathtub Installation
Plumbing Basics: What You Need for Bathtub Installation
Blog Article
We have encountered this article about Tools You Need to Install a New Bathtub listed below on the net and accepted it made good sense to share it with you on my blog.
Installing a bathtub isn't specifically rocket science, but it does call for strong plumbing, carpentry, and also often, tiling abilities. Changing an old tub with a brand-new one is also a reasonably tough job. If the old bathtub is easily available, the project can relocate rapidly; if you have to open a wall surface to remove the old bathtub and position the brand-new bathtub, the task is a lot harder. In either case, the task is within a residence handyman's skills, although you will need an assistant to vacate the old bathtub and set in the brand-new one. Ensure you have actually certified on your own for the task and also are comfortable trying it. Rather than hiring a contractor to take control of a halfway-completed task, it is much better to consider using one prior to you begin. Possibilities are you might need an expert plumber to make tube links.
This short article will certainly help you mount a new tub in your bathroom if you have currently gotten a new bathtub and do not need to transform the arrangement of your previous water supply pipes.
Your devices and product list ought to consist of the following:
Getting ready for the Installation
To start with, the supporting framework supplied with the bathroom needs to be fitted (if required) according to the manufacturer's directions. Next, fit the faucets or mixer to the tub. When suitable the tap block, it is necessary to make sure that if the faucet comes with a plastic washer, it is fitted in between the bathroom as well as the taps. On a plastic bath, it is likewise reasonable to fit a supporting plate under the taps device to avoid stress on the bathtub.
Fit the adaptable tap connectors to the bottom of the two taps using 2 nuts and olives (in some cases supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet via the hole in the bath. Use the nut provided by the maker to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. Make certain you use all of the provided washers.
Attach the catch to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Link all-time low of the overflow tube in a similar manner.The bath should currently be ready to be suited its last position.
Removing Old Taps
If you require to change old taps with brand-new ones as a part of your installation, then the first thing you ought to do is detach the water. After doing so, activate the taps to drain any type of water remaining in the system. The process of eliminating the existing faucets can be rather bothersome because of the limited gain access to that is often the case.
Make use of a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that attaches the supply pipes to the taps. Have a cloth prepared for the remaining water that will certainly originate from the pipelines. When the supply pipelines have actually been eliminated, make use of the exact same device to loosen the nut that holds the taps onto the bath/basin. You will require to stop the solitary faucets from turning throughout this procedure. When the faucets have actually been gotten rid of, the holes in the bath/basin will have to be cleaned up of any kind of old sealing compound.
Prior to proceeding to fit the brand-new taps, compare the pipeline links on the old faucets to the new taps. If the old faucets are longer than the brand-new faucets, after that a shank adapter is needed for the brand-new faucets to fit.
Setting up the Bath tub
Utilizing both wooden boards under its feet, place the tub in the required setting. The wood boards are practical in evenly spreading out the weight of the bathtub over the area of the boards rather than concentrating all the weight onto four small points.
The next goal is to make certain that the tub is leveled all round. This can be accomplished by checking the level as well as adjusting the feet on the bathtub up until the level reads level.
To mount faucets, fit the bottom of the furthest versatile faucet adapter to the suitable supply pipeline by making a compression join; then do the very same for the other faucet.
Switch on the water and also inspect all joints and also new pipework for leakages as well as tighten them if required. Fill up the tub and additionally check the overflow outlet and the regular electrical outlet for leaks.
Finally, fix the bath paneling as explained in the producer's user's manual. Tiling as well as sealing around the tub needs to wait until the bath tub has been used at least when as this will certainly resolve it right into its last placement.
Fitting New Taps
If the tails of the brand-new taps are plastic, then you will require a plastic adapter to stop damage to the thread. One end of the connector fits on the plastic tail of the faucet as well as the other end gives a link to the current supply pipes.
If you require to fit a monobloc, then you will certainly call for decreasing couplers, which links the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next off, position the tap in the mounting hole in the bath/basin ensuring that the washing machines are in place in between the faucet and also the sink. Secure the faucet in place with the maker given backnut. Once the tap is safely in position, the supply pipes can be linked to the tails of the taps. The faucets can either be connected by using corrugated copper piping or with typical faucet ports. The former kind ought to be attached to the tap ends initially, tightening only by hand. The supply pipes can later on be linked to the other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Bathtub
In the area where the bathroom meets the floor tile, it is necessary to secure the joins with a silicone rubber caulking. This is very important as the fitting can move enough to fracture an inflexible seal, creating the water to permeate the wall between the bathroom and the tiling, causing issues with dampness and feasible leaks to the ceiling below.
You can pick from a selection of coloured sealants to blend in your fixtures as well as installations. They are sold in tubes and cartridges, as well as are capable of securing voids approximately a size of 3mm (1/8 inch). If you have a larger gap to fill up, you can fill it with twists of soaked paper or soft rope. Bear in mind to constantly load the tub with water before securing, to allow for the movement experienced when the bathtub remains in use. The sealer can crack relatively early if you do not take into consideration this activity before securing.
Additionally, ceramic coving or quadrant ceramic tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to size, are also quickly available on the marketplace. It is suggested to fit the tiles utilizing water-resistant or water-proof glue as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
:max_bytes(150000):strip_icc()/installing-a-tub-or-shower-surround-2718986-hero-40160398595d4544b639b3398cdb247c.jpg)
Do you enjoy reading about How to Install a Bathtub? Write feedback below. We'd be delighted to know your reactions about this write-up. Hoping that you come back again before long. Do you know anybody else who is occupied with the niche? Why not promote it. I am grateful for your time. Don't hesitate to stop by our site back soon.
For quick fixes, call! Report this page